Live status of the core. Bits [20:11] describe the last line rate request and are laid out the same in the Host and the Device core.
| Bits | Field | Access | Description |
|---|---|---|---|
| [31:21] | reserved | Reserved. | |
| [20:18] | RECONFIG_STATE | RO | Line rate change state: 0 idle, 1 DRP writes, 2 reset held, 3 waiting for the reset to be taken, 4 waiting for reset done. |
| [17:16] | RECONFIG_RETRIES | RO | Extra PLL resets the last request needed. |
| [15:14] | RECONFIG_ERR_CODE | RO | Error of the last request: 1 DRP no answer, 2 reset not acknowledged, 3 transmitter reset done never back. |
| [13] | RECONFIG_ERR | RO | The last request failed. |
| [12] | RECONFIG_PEND | RO | A request is latched and not yet launched. |
| [11] | RECONFIG_BUSY | RO | A line rate change is running. |
| [10] | HS_STREAM_ACTIVE | RO | The stream is on. |
| [9] | HS_HRTBT_DONE | RO | Heartbeat generator idle. |
| [8] | HS_EVENT_FIFO_FULL | RO | Event FIFO full. |
| [7] | HS_EVENT_FIFO_RST | RO | Event FIFO in reset. |
| [6] | HS_CNTRL_FIFO_FULL | RO | Acknowledge FIFO full. |
| [5] | HS_CNTRL_FIFO_RST | RO | Acknowledge FIFO in reset. |
| [4] | LS_CNTRL_FIFO_EMPTY | RO | Received command FIFO empty. |
| [3] | LS_CNTRL_FIFO_RST | RO | Received command FIFO in reset. |
| [2] | LS_WORD_ALIGNED | RO | Uplink receiver word aligned: a Host is there. |
| [1] | LS_BYTE_ALIGNED | RO | Uplink receiver byte aligned. |
| [0] | TX_RESET_DONE | RO | Transmitter reset done. |
Set when the stream or the test path does not confirm an on or off request within ACK_TIMEOUT. Any flag raises ACK_ERR.
| Bits | Field | Access | Description |
|---|---|---|---|
| [31:4] | reserved | Reserved. | |
| [3] | TEST_OFF | W1C | Test packets off not confirmed. |
| [2] | TEST_ON | W1C | Test packets on not confirmed. |
| [1] | STREAM_OFF | W1C | Stream off not confirmed. |
| [0] | STREAM_ON | W1C | Stream on not confirmed. |
Writing bit 3 = 1 starts a line rate change to the speed in bits [2:0]: the core rewrites the transceiver PLL and dividers over DRP, resets the PLL and datapath, and waits for the transceiver to come back. A request that arrives while one runs is kept (newest wins) and runs next. Progress and errors are in CXP_STATUS[20:11]; the RATE_DONE and RATE_ERR interrupts report the end. The Device refuses rate code 7 with SLVERR.
| Bits | Field | Access | Description |
|---|---|---|---|
| [31:4] | reserved | Reserved. | |
| [3] | APPLY | RW | 1 = start the rate change. |
| [2:0] | RATE | RW | Line rate code, CXP-1 to CXP-12. The supplied driver holds the code table. |
Bit 0: CXP 2.x operation (tagged commands, heartbeat). Bit 1: extra low-speed trigger.
| Bits | Field | Access | Description |
|---|---|---|---|
| [31:2] | reserved | Reserved. | |
| [1] | LS_TRIG_EXTRA | RW | Extra low-speed trigger. |
| [0] | CXP2 | RW | 1 = CXP 2.x: tagged commands and heartbeat. |
| Offset | Name | Access | Meaning |
|---|---|---|---|
| 0x054 | CXP_ERRORS_HS | W1C | Sticky flags of the downlink packet builders, including errors in an acknowledge built by firmware (bits [6:0]). Write 1 to clear. Any flag raises HS_ERR. |
| 0x058 | CXP_ERRORS_LS | W1C | Sticky flags of the uplink receiver. Write 1 to clear. Any flag raises LS_ERR. |
| 0x068 | CXP_STREAM_PCKT_MAX | RW | StreamPacketSizeMax agreed with the Host. 0 = no stream packets. |
| 0x0B0 | CXP_TX_MSTR_ID | RW | The MasterHostConnectionID written by the Host at discovery. Goes into event and heartbeat packets. |